- Air operated pressure brake bleeder
- Portable - can be disconnected from air supply
- Stores pressure inside tank
- Supplied with master cap adaptor kit ALB30564
- Suitable for clutch bleed as well as brake bleed
- 5 Litre capacity tank
-
Part no. ALB30566
Pressure Brake Bleeder
-
Part no. ALB40331
Electric & Hybrid Full Starter Kit
Electric & Hybrid Full Starter kit. Everything you need to start servicing Electric & Hybrid Vehicles Safely Kit Contents- ALBRPK3610-RW - Barrier Chain with Rubber base Posts kit (Red & White)
- ALBIRP2920 - Insulated Rescue Pole
- ALBESP7299 - Safety Poster - ELECTRIC SHOCK POSTER
- ALBHVE7750 - Safety Poster HIGH VOLTAGE ELECTRIC SHOCK
- ALBRIM2311 - Electrical Insulating Rubber Mat to IEC61111 - 1m x 1m Mat
- ALBKLS4237 - EHV Lockout Station for Vehicle Keys & Padlocks
- ALBLOP7943 - Lockout Safety Padlock - Long Shackle (x2)
- ALBKLT7050 - Lockout CAR KEY tags for EHV(re-usable)x10 with marker pen
- ALBLOT4148 - Lockout Padlock tags for EHV(re-usable)x5 with marker pen
- ALBLNH7942 - Lockout Safety Nylon Hasp - use with tasg &/or SWC
- ALBSWL4721 - Steering wheel Lockout with Warning Sign
- ALBSGK6955L - Electrical Safety Glove Kit - Large
- ALBCUG6915 - Cotton Under gloves x12 pairs
- ALBEAF8532 - Electric Arc Protector Face Shield Visor - Lightweight
- ALBFSB8590 - Face Shield Protective Storage Bag
- ALBA18-LIGHTENING - EHV Electrical safety Boot (sizes 6-9 confirm size)
- ALBRTP7234 - EHV Roof Top Warning Sign
- ALBTCS6639 - High Voltage No Admittance Sign Rigid 400 x 300mm
- ALBIPS7221-HV - Sign ISO Pictogram - High Voltage
- ALBHVS7561 - High Voltage Re-usable Adhesive Sticker (x10)
- ALBHVT8049 - High Voltage Vehicle Tags (x10)
- ALBCES7550 - Insulated Cable Shrouds 18&24mm (x10)
- ALBMIT4094 - EHV Multimeter with Insulation Test CAT111 to 1000VDC
- ALBNVP4025 - No Voltage Present Detector - CAT111 Certified
- ALBSDT4672 - Disconnect Shut Down timer for EV's
- ALBEVT6150 - Insualted Tool Kit 3/8" Drv 25PCS
- ALBEVT5515 - Insulated Hex Key Set Extra Long 6PCS VDE Certified
- ALBEVT7751 - Insulated Star Key Set Extra long 9PCS VDE Certified
- ALBEVT7885 - Insulated Inspection Mirror 50mm - EN/IEC 60900:2012 1000V
- ALBEVT7211 - Insulated Magnetic Pick Up Tool
- ALBEVT7551 - Insulated Trim/Cable mgmt set 4PCS
- ALBITS1301 - Insulated Transparent Shroud 1000V 1M x 1.3M
- ALBIPC6025 - Insulated Clamp To secre Shroud Material (x2)
-
Part no. ALBCPK3612-RW
Post & Chains Red/White 6 Post Set with Fillable Bases
The barrier chain and 6 post kit is supplied with:- 12.5 metres of plastic barrier chain.
- 6 x Chain Support Posts with fillable bases.
- 10 x “S” hooks to attach the chain to the posts.
-
Part no. ALBSWL4721
Steering Wheel Lockout with Warning Sign
Steering Wheel Lockout with integral Warning Sign. A high visibility warning to alert unauthorised personnel that the vehicle is being serviced or repaired, therefore should not be moved or started. The sign is an integral component of the key locked steering wheel immobiliser to prevent unauthorised removal.- “Technician in charge” can be inserted on the sign
- Dry-wipe Marker Pen included
- Supplied with 2 keys
-
Part no. ALBTCS6639
High Voltage Warning/No Admittance Sign
Electric & Hybrid Vehicle combined Danger High Voltage / No Access sign.- Inform customers of the dangers, and that access is for authorised personnel only.
- Printed on a 3mm polymer panel.
- Size: 300 x 400mm
-
Part no. ALBSGK6955
Insulated Gloves Set
The Electrical Safety Glove Kit with Storage Case contains:- Cotton Under Gloves (12 pairs)
- Electrical Gloves – Insulate to 1,000V Class 0 (1 Pair)
- Leather Over-Gloves (1 Pair)
- 1 x Safety Glove Storage Box
- Essential PPE when working on high voltage systems
- Electrical Gloves – Insulate to 1,000V (Class 0)
- Cotton under-gloves improve dexterity and user comfort
- Leather over-gloves protect the rubber insulating gloves from mechanical damage
- Robust polypropylene storage case to protect gloves
-
Part no. ALBSDT4672
Disconnect Shut Down Timer
Disconnect and shut down digital timer used to accurately measure the required shut down period between switching off the ignition and disconnecting or reconnecting the vehicle’s battery etc. Particularly important where airbag, BSI, hybrid and electric vehicle ECU’s need time to shut down before proceeding with further work. Suitable for technicians working on hybrid and battery electric vehicles on a regular basis.- Dimensions: 70(H) x 70(W) x 25(D)mm
- Material: Plastic
- Weight: 46g
- Colour: White
- Rear magnet and fold out stand
- Large digital display is easy to read at a glance
- Requires 1x AAA battery (supplied)
-
Part no. ALBRTP7234
Double Sided Vehicle Roof High Voltage Warning Sign
The Electric Vehicle Roof Top Warning Sign.- High visibility warning to all employees of Electric or Hybrid vehicles being present in the workshop.
- Constructed from durable rigid plastic.
- Foam protected feet to prevent damage to the vehicle bodywork.
- Size: 310mm x 235mm x 3 sides.
-
Part no. ALBRPK3610-RW
Posts & Chains Red/White with Solid Composite Base
The Red & White barrier chain with rubber base and 6 post kit is supplied with:- 12.5 metres of plastic barrier chain.
- 6 x Posts with Rubber Bases
- 10 x “S” hooks to attach the chain to the posts.
-
Part no. ALBRIM2311
Insulated Floor Matting 1sq mtr
Insulating Rubber Mat 1m Electrical Insulating Rubber Matting is essential for ensuring the safety of technicians whilst working on Electric and Hybrid Vehicles. Manufactured to the international standard IEC 61111 Class 0, offers protection up to 1,000 volts. produced with a ribbed profile giving it an increased surface area, which helps to disperse electrical discharge and offers anti-slip properties. Size: 1m x 1m -
Part no. ALBNVP4025
Cat1V High Voltage Tester
The No Voltage Present Detector is essential equipment for Hybrid and Electric vehicle technicians to prove that there is no voltage present prior to working. A simple LED scale indicates the voltage range present at the time of testing. An independent ELV indicator shows if >50VAC / 120VDC is present even if there is no battery power to the unit or the main circuit has failed. The NVP4025 No Voltage Present Detector has a safe test range from 12V to 1,000V AC/DC. Voltage measurement is in increments as follows: 12, 24, 50, 120, 230, 400, 690 & 1,000 Volts. Conforms to the following safety standards:- BS EN61243-3
- TUV-GS38
- EN61010-1 CAT III – 1,000V
- EN61010-1 CAT IV – 600V
-
Part no. ALBMIT4094
Cat111 Multimeter c/w Insulation Test Function
The EHV Multimeter and Insulation Tester is a true RMS multi-meter designed for testing and checking components on electric and hybrid vehicles through the continuity test and diode test. The multimeter function is combined with an inbuilt Insulation Test facility making it ideal for troubleshooting and preventative maintenance. The Insulation test function operates at the following test voltages: 50v, 100v, 250v, 500v and 1000v. The EHV Multimeter and Insulation Tester is supplied with all test leads and clips, temperature probe, manual and batteries. Complies with EN61010 CATEGORY III (1000v) and CATEGORY IV (600v) -
Part no. ALBLOT4148
Lockout Safety Tags – Do Not Start
Our Lockout Tags are designed to be used with Insulated Safety Lockout Padlocks (LOP4540) when securing the Isolation Port (MSD) Lockout Device (FLD4566) or Steering Wheel Warning Cover. Manufactured from gloss laminated polyester to ensure durability and moisture resistance. A 10mm brass eyelet ensures the Lockout Tags cannot be torn off. High visibility warning printed in vibrant colour on one side, with “Technician In Charge” name panel on the reverse. Supplied with a fine point, dry wipe, marker pen for the “Technician In Charge” to identify themselves. When used with the dry wipe marker the Tags can be reused many times. Dimensions: 140 x 80mm Pack Size: 5 tags with 1 x fine point, dry wipe, marker pen. -
Part no. ALBLOP7943
Lockout Safety Padlock – Long Shackle
Lockout Safety Padlock - Long Shackle. Used to prevent unauthorised access and accidental activation of high voltage systems on electric vehicles- Non-conductive nylon body.
- 76mm shackle.
- Use with lockout key tags.
-
Part no. ALBLNH7942
Lockout Safety Nylon Hasp
The Lockout Nylon Hasp allows you to prevent access where standard padlocks are not long enough. Supplied with 6 holes so that multiple padlocks can be used when more than one operative should restrict access.- Can be used with lockout tags.
- Dimensions: 193mm long x 41.5mm wide.
- Hasp length: 101mm; hole diameters: 10mm.
-
Part no. ALBKLS7050
Lockout Safety Tags
Car Key Lockout Tags are manufactured from gloss laminated polyester to ensure durability and moisture resistance. High visibility warning printed in vibrant colour on one side, with “Technician In Charge” name panel on the reverse and space for Vehicle Registration No. Supplied with a fine point, dry wipe, marker pen for the “Technician In Charge” to identify themselves. When used with the dry wipe marker the Lockout Tags can be reused many times. Dimensions: 50 x 70mm Pack Size: 10 tags with 1 x fine point, dry wipe, marker pen & tie wraps. -
Part no. ALBKLS4237
Lockout Management Station
The Lockout Station securely stores vehicle keys, Isolators (MSD) and Lockout Padlocks. Manufactured from pressed metal plate. Isolators and Padlocks NOT included (sold separately). Dimensions of: 20 x 16 x 7.5cm. Supplied with 2 keys. -
Part no. ALBITS1301
Insulated Transparent Shroud 1000v
Transparent Insulating Shroud, certified for safe work up to 1,500VDC. Should be used to isolate the engine compartment on Electric and Hybrid vehicles to prevent accidental contact with live components- Heavy Duty, fireproof PVC
- Certified to IEC 61112 Class 0 (1,000VAC / 1,500VDC)
- Dimensions: 1.3m x 1.0m x 0.8mm
-
Part no. ALBIRP2920
Insulated Rescue Pole c/w Mounting Brackets
An electrically insulated rescue pole with hook, 1.45 metres long and rated to 45kV supplied with wall mounting brackets. Designed to safely remove victims of electric shock from danger. Conforms to NF EN 50508. -
Part no. ALBIPS7221-HV
High Voltage Sign (for wall, door or vehicle fixing)
“High voltage” ISO Pictogram denotes a Hazard or Prohibition message without text.- Suitable for use throughout Europe.
- Printed on a durable polymer panel measuring 25 x 20cm
- Fitted with a durable sucker to allow placement on any smooth surface.
-
Part no. ALBIPC6025
Insulated Clamp to secure Shroud material
Insulated Spring Loaded Plastic Clamp for shroud. Spring-loaded plastic clamp for securing engine bay protective shroud.-
- Dimensions: 165 x 82 x 18mm
- Jaw opening: 25 mm
- Insulation rating to 1,000 Volts
-
-
Part no. ALBHVT8049
High Voltage Vehicle Tags
High Voltage Vehicle Identification Tags. Manufactured from lightweight PVC and designed to be deployed on the vehicle rear view mirror or indicator stalk. Provides a visible warning of potential high voltage danger.- Designed to serve as a warning that vehicle is EV or hybrid.
- Ideal for workshops, or car hire companies to hang inside customer cars.
- Provides additional safety warning to identify hybrid/EV vehicles.
- Size: 177 x 66.5mm.
- Can hang on internal rear view mirror, steering wheel or indicator stalk.
- Supplied in pack of 10.
-
Part no. ALBHVS7561
High Voltage Re-Usable Adhesive Sticker Pack of 12
High Voltage Warning Vehicle Stickers - re-useable. Designed to indicate high voltage areas on an EV, such as charging port, battery, capacitor bank etc. These reusable vinyl labels have a low-tack adhesive which does not leave residue on the vehicle and enables them to be used many times.- Indicates high voltage parts of the vehicle.
- Label dimensions: 150 x 75mm.
- Supplied in a pack of 12.
-
Part no. ALBHVE7750
Electric Shock First Aid Poster- High Voltage Version
Electric Shock First Aid and CPR Advice Polymer Poster.- The High Voltage Electric Shock Safety Poster is printed on a durable polymer panel.
- Displays an easy to follow casualty assessment guide and CPR instructions.
- Size: 750 x 500mm.
-
Part no. ALBITK1229
Insulated Tool Kit 1/2″D 29pc
Insulated Tool Kit, ½” Drive, VDE Certified for live working up to 1,000V AC / 1,500V DC. Supplied with 6pt sockets ranging from 10mm - 27mm, hex keys, ratchet wrench, extension bars, adjustable spanner, pliers and screwdrivers. A comprehensive set of tools to cover most service and repair needs when working on Electric and Hybrid vehicles.- 13 x 1/2"Dv. Insulated Socket - 10, 11, 12, 13, 14, 16, 17, 18, 19, 21, 22, 24, 27.
- 4 x 1/2"Dv. Insulated Hex/Allen Extra Long Socket - 4, 5, 6 and 8mm – 120mm long.
- 2 x 1/2"Dv. Insulated Extension Bar 125mm and 250mm.
- 1/2"Dv. Insulated T-handle Wrench 200mm
- 1/2"Dv. Insulated Reversible Ratchet 250mm
- Insulated Combination Plier 180mm
- Insulated Side Cutter 160mm
- Insulated Snipe/Long Nose Plier 160mm
- Insulated Adjustable Wrench 200mm
- 2 x Insulated Screwdriver - Slotted - 4.0x100mm and 5.5x125mm
- 2 x Insulated Screwdriver – Phillips - PH1x80mm and PH2x100mm
- VDE/GS certified and IEC60900 approved for safe work up to 1,500 Volts DC.
-
Part no. ALBEVT7885
Insulated Inspection Mirror
1000v Insulated Inspection Mirror, for use when working on electric vehicles.
- Ideal for the inspection of High Voltage Cables & Connectors in confined areas. For e.g. such as battery packs, controller & difficult to get to under vehicle areas.
- Insulated Rubber moulded casing for easier handling.
- 50mm diameter mirror disc.
- 170mm handle length.
- Manufactured from non-conductive materials.
- Manufactured & Tested to EN/IEC 60900:2012 Standard, for up to 1000V live working.
- Made in the UK.
-
Part no. ALBEVT7751
Insulated Torx Key Set 9pc
9 Piece Insulated STAR / Torx / Torx head Key set – VDE Certified Sizes: T10/T15/T20/T25/T27/T30/T40/T45/T50 Manufactured from S2 steel for strength -
Part no. ALBEVT7551
Insulated Trim / Cable Management Tool Set 4pc
Insulated Trim and Cable management tool set. Used to safely remove vehicle trim and clipped components on Electric and Hybrid vehicles.- Four profile shapes to assist with removal of various trim clip styles.
- Tested to 1,000 volts.
- Supplied with storage pouch.
-
Part no. ALBEVT7211
Insulated Magnetic Pick-Up Tool
Insulated magnetic pick up tool with long reach, ideal for retrieval of dropped fasteners and small components.- Approved for live working up to 1,000Volts.
- An essential tool for electric vehicle maintenance technicians.
- Lifting capacity up to 250g.
- 5mm diameter magnetic head.
- 420mm long reach with insulated shaft and handle.
-
Part no. ALBEVT6150
Insulated Tool Kit 3/8″D 25pc
Insulated tool set, for live working up to 1,000V AC / 1,500V DC. Supplied with sockets and Open End Spanners, ranging from 7mm - 22mm. Also includes; pliers, screwdrivers and a cable knife.- 9 x 3/8"D sockets: 7, 8, 10, 12, 14, 15, 17, 19, 22mm. Length: 71mm.
- 3/8"D 72 teeth ratchet; extension bar 100mm; T-handle.
- combination pliers 175mm; side cutter 150mm.
- 6 x Open End Spanners: 7, 8, 10, 12, 14, 17mm.
- 1 x Cable Knife.
- 4 x Screwdrivers: Phillips: Ph1 x 100mm, Ph2 x 100mm; Flat: 5.5 x 125mm, 4 x 100mm.
- VDE/GS certified and IEC60900 approved for safe work up to 1,500 Volts DC.
-
Part no. ALBEVT5515
Insulated Hex Key Set 6pc
6 Piece Insulated Hex key set Extra Long (VDE Certified) tested to 1000volt. Sizes: 2.5mm/3mm/4mm/5mm/6mm/8mm. -
Part no. ALBESP7299
Safety Poster – Electric Shock
This poster gives basic advice on what to do in an emergency when someone has an electric shock. Printed on a flexible PVC panel, to ensure good moisture and dirt resistance. Suitable for use in any workplace. -
Part no. ALBA18-Lightening
Electric EV Safety Work Boots
High voltage is now a critical factor in personal safety due to the latest generation of electric and hybrid vehicles. The safety boot is fully compliant and fully electrically insulated. They meet all UK and EU requirements for safety footwear, along with international standards for high voltage (1000v). Size: UK 6-14 (Whole Sizes) -
Part no. ALBEAF8532
Arc Flash Face Shield
- A robust, heavy-duty, helmet mounted face shield with hearing protection compatibility. Polycarbonate browguard with ratchet headband. Full wrap-around visor. Conforms to: EN 166 B 3.9
-
Part no. ALBCUG6915
Cotton Liner Gloves
- Cotton Under Gloves should be worn underneath the Electrical Insulating Gloves to improve comfort and hygiene. The use of the cotton under gloves also improves the fit of the safety gloves and improves dexterity.
-
Part no. ALBCES7550
Insulated Cable End Shrouds
Insulated Cable End Shrouds for Electric and Hybrid vehicles. Used to insulate and protect cable terminal ends during component replacement. Specially moulded to incorporate a self-grip collar. Supplied in a pack of 10 sleeves, 5 of each two sizes. 5 of 18mm OD x 14mm ID x 100mm long 5 of 24mm OD x 20mm ID x 100mm long -
Part no. ALB580A240V
Analogue Pressure Brake Bleeder 0.5-4.0, 6 Litre, 240V
Pressure bleeding is the only method approved by brake manufacturers- Full fluid change can be completed by a single operator in approx. 15 minutes
- Heavy duty pump for longer life & continuous use
- Fully adjustable analogue pressure regulator, 0.5-4.0 bar
- No compressed air used, therefore no possibility of contamination of the fluid
- Storage facility for fluid collection container & accessories (ALB30564B Cap kit)
- Suitable for use on Car & LCV brake systems & also on HGV clutches
- 6L fluid change capacity
- 220V/240V 50HZ/60HZ mains operated
- Stainless steel construction
-
Part no. ALB599A
Pressure Brake Bleeder: 0-3.0 BAR, 5 LITRE, 230V
- Full fluid change can be completed by a single operator in approx. 15 minutes
- Fully adjustable pressure regulator 0 – 3.0 bar
- Draws fluid direct from 5L container
- Auto cut-off prevents air entering system if fluid supply is interrupted
- Portable unit with carry handle – only 9.0kg
- 220V/240V 50HZ/60HZ mains operated
- Heavy duty pump for long life
- Coiled brake fluid delivery hose for ease of use and storage
- Supplied complete with ALB30564B; multi-vehicle cap and European cap kit
- OEM approved
-
Part no. ALB30913B
Multi Voltage Glow Plug Tester
• Works on all types of glow plugs - any voltage • Displays Open & Short Circuit • Measures actual glow plug resistance for evaluation of the plug specification • Shrouded quality leads • Internal 9 volt battery & low warning indicator • Protected with oil resistant rubber shroud -
Part no. BFA8602
First Aid Kit for Burns inc. H/F Antidote Gel
- To treat burns caused by heat and electric arc
- Includes antidote gel for Hydrofluoric Acid exposure
- Supplied with integral wall mount bracket
-
Part no. FSB8590
Face Shield Protective Storage Bag
- Prevents damage to the Face Shield visor
-
Part no. DMO2017L
Electrically Insulating Dielectric Over-Boots
- High voltage protection up to 20,000V
- Approved to European standards
- Fuel and oil resistant rubber sole
-
Part no. EAF8532
Face Shield (dielectric)
- Heavy duty dielectric face shield
- Full wrap-around visor
- Polycarbonate brow guard
- Ratchet adjustable headband
- Conforms to EN166B3.9
-
Part no. ALB40320
Borescope with Camera & Video
- Detect the invisible inside parts of machinery (such as cars) to check whether it is working normally.
-
Part no. ALB40318
Lugdriller
• Removes the most difficult locking lug nuts • Professional kit : made of solid material that can work on the hardest lugs • Very easy and quick to use : takes less than 10 minutes. -
Part no. ALB40317
Universal Diesel Injector Puller
This extractor allows the user dismantle Common rail or Piezo injector types for Denso, Siemens, Bosch & Delphi brands from 1999 to 2017. -
Part no. ALB40316
Hub Cleaner Plastic
- Plastic bell 1/2" sq dr - for use with pneumatic impact wrenches
- Corrosion between the wheel rim and the wheel hub is removed effectively
- Torque valves no longer distorted by a build up of corrosion
- Complete with 1 abrasive cleaning disc - 150mm diameter
-
Part no. ALB40315
Disposable Visors
- Non-medical
- Disposable Visor Specifications:
- One size fits all
- Head size 49cm to 64cm
- Screen dimensions 16.7cm x 21cm
- Cardboard headpiece – fully recyclable – 500um white folding box-board
- Anti-mist film – 71um poly
-
Part no. ALB40308
Roki Steel Brush
The Roki wire brush range has been manufactured in co-operation with the automobile industry, designed for cleaning off clogged lining deposits when changing brake pad linings. This brush is very slim with a heavy-duty straight stainless steel wire filling, made this way to prevent damage to sensitive brake areas during use. Heavy duty brake caliper brush with 2 rows of heavy duty steel wire and ergonomic handle -
Part no. ALB40307
Roki Brass Brush
The Roki wire brush range has been manufactured in co-operation with the automobile industry, designing for cleaning off clogged lining deposits when changing brake pads linings. This brush is very slim with crimped brass wire filling, made this way to prevent damage to sensitive brake areas during use. Heavy duty brake caliper brush with 2 rows of heavy duty brass wire fill and ergonomic handle -
Part no. ALB40305
25-50mm Micrometer
- Range: 25-50mm
- Display Type: Non-Digital
- Carbide Measuring Faces
- Clear Graduations on satin chrome finish
- Hammertone baked enamel finish
- Ratchet stop
- When the reference rod is used as the measured workpiece, the "0" position can be corrected Supplied in fitted plastic case
-
Part no. ALB40302
0-25mm Micrometer
- Range: 0-25mm
- Display Type: Non-Digital
- Carbide Measuring Faces
- Clear Graduations on satin chrome finish
- Hammerstone baked enamel finish
- Ratchet Stop
- Supplied in fitted plastic case
-
Part no. ALB40292C
EV Battery Lift (Hydraulic and Electric) 1.0T
- Electric hydraulic drive , 24V safety voltage control, good security.
- The base is mounted with four universal wheels for easy movement of the lift.
- The handle can be adjusted to the level facilitate the lifting of the power battery
- With minimum and height limits
- There are many M10 threaded holes on the surface of the platform to facilitate the installation of positioning kits, suitable for different types of vehicles.
- Sliding blocks adopt oil free super-wearable materials.
- The sliding platform can be moved 40mm in-plane.
- With hydraulic lock and mechanical dual-gear safety-claw lock double safety device, adversely, safe and reliable.
-
Part no. ALB40292B
EV Battery Lift (Hydraulic & Electric) 1.2T
- Split table and tapped top plate
- Double safety guarantee: hydraulic and mechanical safety lock
- Providing the lowest and highest height limit to ensure safe operation
- With a platform leaned all round and moving horizontally, it is a good helper for the installation and maintenance of vehicle battery or engine
- It's easy to move the platform with hydraulic lifting trailer
- Capable of lifting vehicle battery / engine within 1200kg
- Equipped with adjusting handle to make operation more convenient
- Thanks to the gimbaled level, the users could monitor the real-time horizontal position of the platform
-
Part no. ALB40292A
EV Battery Lift (1T)
ALB40292A; suitable for lifting electric vehicle batteries weighing max1000kg. Suitable for use in installation & dismantling of new electric vehicle batteries. 4 castors with brakes Adjustable lowering speed Tilted platform design ensures secure fit to battery pack -
Part no. ALB40296A
Drive Pro 12/24 Lithium Starter
Multifunction 12V/24V lithium starter, equipped with: - two USB outputs (1A-2,1A) to charge (power bank) electronic devices (tablets, smartphones, etc.), - high intensity LED lights with three function modes for fixed or emergency lighting. It uses high-efficiency LiPO lithium polymer cells that provide rapid and complete charging, constantly monitored by a series of LEDs. Compact and strong it is designed for the professional use. Protection against polarity reversal. Complete with starting cables, cigarette lighter plug and wall charge. -
Part no. ALB40295A
Doctor Charge 50 230V 6/12/24V Battery Charger
ALB40295A DOCTOR CHARGE 50 230V 6V/12V/24V (Charger/starter) Electronic BATTERY MANAGER for total maintenance of WET, GEL, AGM, MF, SPIRAL, START-STOP batteries at 6/12/24V and for support activities when intervening on vehicles in workshops, repair shops and car dealer premises. The innovative Power Stream technology guarantees better performance, up to 50% more than traditional battery chargers. The Pulse Tronic technology guarantees optimal battery charging over 8 phases. Doctor Charge 50 carries out 5 functions: 1. automatic charge and maintenance of batteries with PULSE TRONIC technology, even in difficult environmental conditions (low temperatures); 2. battery tests such as voltage at terminals, starting capacity (CCA) and operational check of the vehicle alternator; 3. recovery of sulphated or very discharged batteries, and recovery of optimal operation with periodic regeneration; 4. stable power supply source for battery changes (to protect the on-board electronics), for diagnostic activities (operation checks carried out on the vehicles), for keeping the batteries of display vehicles in showrooms operational; 5. vehicles start aid. Based on the SMPS (Switch Mode Power Supply) Technology. In case of black-outs or repetitive uses Doctor Charge 50 can set itself at the last settings carried out, furthermore the cables can be calibrated according to their type (different lengths and/or sections). Many protections available. Fit with PFC device. -
Part no. ALB40294A
Flashstart 700
- 12V battery less starter (ultra-condensers technology).
- It starts a large fleet of vehicles even at low temperatures. No maintenance require: Flash Start exploits the residual battery power to start the vehicle.
- It can be charged via USB or a 12V cigarette lighter socket.
- GLOW function for starting diesel engines at low temperatures.
- Protection against short-circuits and polarity reversal.
- Supplied with a charger cable with cigarette lighter plug (12V) and a hexagonal wrench (for the battery terminals on-board the vehicle).
-
Part no. WF80-P
Alba Safety Trainer
- Suede upper
- Steel toe cap
- Dual density polyurethane sole
- Penetration resistant midsole
- Oil resistant sole
- Sizes: 8-11 in stock, other sizes available to order
-
Part no. WF70-P
Alba Safety Boot
- Suede upper
- Steel toe cap
- Dual density polyurethane sole
- Penetration resistant midsole
- Oil resistant sole
- Sizes 8-11 in stock, other sizes available to order
-
Part no. WF2-P
Waterproof Leather Safety Boot
- Black full grain leather
- Semi Goodyear Welt / Cemented Rubber
- Oil & Acid Resistant
- Steel toe cap
- Steel Eyelets/Steel Hooks
- Sizes 8-11 in stock, other sizes available to order
-
Part no. ALB40301
Doctor Charge 130 230V 6/12/24V Battery Charger 90A
Electronic BATTERY MANAGER for total maintenance of WET, GEL, AGM, MF, PbCa, EFB and Li batteries at 12/24V and for support activities when intervening on vehicles in workshops, repair shops and car dealer premises. The innovative Power Stream technology guarantees better performance, up to 50% more than traditional battery chargers. 1.The Pulse Tronic technology guarantees optimal battery charging over 8 phases. 2. battery tests such as voltage at terminals, starting capacity (CCA) and operational check of the vehicle alternator; 3. recovery of sulphated or very discharged batteries, and recovery of optimal operation with periodic regeneration; 4. stable power supply source for battery changes (to protect the on-board electronics), for diagnostic activities (operation checks carried out on the vehicles), for keeping the batteries of display vehicles in showrooms operational; 5. vehicles start. Based on the SMPS (Switch Mode Power Supply) Technology.In case of black-outs or repetitive uses Doctor Charge 130 can set itself at the last settings carried out. Many protections available. Fit with PFC device. -
Part no. ALBGLD-40A
GLD-40 Smoke Wizard
The advanced smoke wizard GLD40 combines pressure and vacuum leak measurement for Evaporative Emission (EVAP) and general purpose leak detection in a compact design. Uses automotive system safe, OEM-approved UltraTraceUV dye smoke solution, the smoke that won't stink! To find the leak when the smoke is gone or when the leak(s) may be hidden and disassembly is required, use the included combination light to see the dye and pinpoint the exact leak location -
Part no. ALB40252
Starter Set- Brake Bleeder Cap Adaptor Kit
- Set of 6 specialist cap adaptors:
- ALB560-11 (Applications: Nissan Qashquai 2009-, Primera, Radius, X-Trail, Renault Koleos)
- ALB40014 (Applications: Nissan Pixo 2009-, Suzuki Alto / SX4)
- ALB40015 (Applications: Nissan Micra 2011-, Nissan Kubistar, Cabstar, Urvan)
- ALB30903 (Applications: Standard E20 thread Eurocap)
- ALB30912 (Applications: Ford Fiesta 2010 onwards)
- ALB40162 (Cross brand adaptor)
-
Part no. ALB40100
Asian Cap Adaptor Set
- Set of 5 specialist Brake master cylinder caps for Asian vehicles
- ALB560-11 (Applications: Nissan Qashquai 2009-, Primera, Radius, X-Trail, Renault Koleos
- ALB40114 (Applications: Nisan Pixo 2009-, Suzuki Alto / SX4)
- ALB40115 (Applications: Nissan Micra 2011-, Nissan Kubistar, Cabstar, Irvan)
- ALB560-12 (Applications: Ford Escape / Kuga)
- ALB30644B (Applications: Standard E20 thread Euro Cap with swivel elbow)
-
Part no. ALB40025A ALB40026A ALB40015A
Trolley Jacks
- A range of High Quality Trolley Jacks, with additional built-in safety features:
- Multi-position ergonomic handle with rubber comfort grip
- Low noise Polyamide Wheels (steel wheels on 6Tonne model)
- Tools holding tray on all models
- Food Pedal for fast approaching lift to load height
- "Dead man" safety lowering control system
- Safety overload & hydraulic stroke limitation
- Made in EU - manufactured to EN1494 European standards.
-
Part no. ALB30570
Pressure Brake Bleeder: 3 Litre – Hand Operated
- Easy one-person operation
- Simple hand pump operation to create pressure
- Supplied with ALB30644 European cap adaptor with swivel elbow 42.8mm
- 3L capacity
- Quick release coupling, pressure relief valve, and 5 bar pressure gauge, suitable for use with all Alba caps.
- ALB30583 Multi Vehicle Cap for ALB30570
- ALB30570-1 Replacement seal
- ALB30570-2 Replacement pump assembly
-
Part no. ALB30564B
Multi Vehicle Cap Adaptor Set
- Suitable for use with most pressure bleeders (including ALB560AB, ALB580A, ALB585A, ALB595A, ALB598A, ALB599A, ALB30570).
- Contents: European cap adapter E20 thread
- ALB592B patented multi-vehicle cap (30-85mm diameter)
- Brake bleed bottle
- Syringe (for fluid level reset if required in master cylinder)
-
Part no. ALB30564A
Cap Kit
- Suitable for use with most pressure brake bleeders
- Includes section of 11 different types/sizes of brake master cylinder caps
- European cap adaptor
- Multi-vehicle cap adaptor
- 3x Chrysler / Jeep / GM cap adaptors
- 5 x specialist cap adaptors covering BMW/Audi, Honda, Hyundai, Mitsubishi, Mazda, Nissan etc
- 1 x specialist cap adaptor for Toyota / Lexus
- Syringe for fluid level reset
-
Part no. ALB620A
Hydragas Suspension Pump
- Fits all Hydrolastic/Hydragas Suspension Systems
- Portable, robust & can be easily used for roadside repairs
- Low Loss Connector allows secure connection to vehicle with no loss of fluid/pressure during connection or disconnection
- Fast & efficient pressuring of vehicle systems- Operates up to 1000psi
- Any air in the vehicle system can be easily removed by pressuring to the approximate trim height, then momentarily releasing the pressure into the pump reservoir
- Trim height chart included
-
Part no. ALB30597
Digital Brake Drum Measuring Tool
- Measurement Range: 0-300mm (metric and imperial)
- Resolution: 0.01mm
- Accuracy: 0.01mm
- Sturdy plastic case
-
Part no. ALB40271
Brake Piston Wind Back Adaptor Kit BMW/Mini
- Set of 6 rewind adaptors specifically for BMW/Mini models
- For use with any 3/8" Sq Dr caliper rewind tool (air or manual)
- Can be used with ALB30990, ALB30845, ALB30728, and ALB30783
-
Part no. ALB40016A
Mobile Tool Cabinet – 3 Drawer
- Internal drawer locking mechanism
- Spring loaded keys to avoid accidental snapping
- Ball bearing slides
- Internal rubber drawer liners
- Non-slip rubber top mat
- 2 static wheels / 2 locking wheels (125 x 38mm - 5" x 1.5")
- Drawer dimensions (internal):
- Drawer 1 : width 58.5cm x depth 40.5cm x height 8.5cm
- Drawer 2 : width 58.5cm x depth 40.5cm x height 8.5cm
- Drawer 3 : width 58.5cm x depth 40.5cm x height 13.5cm
- Lower compartment: width 61cm / depth 42.5cm / height 26.5cm
- Overall dimensions 690 x 460 x 735mm
-
Part no. ALB40098
Multi Storage Container
- 12x clear plastic internal compartments - three different sizes
- Ideal for nuts, bolts, screws, etc
- The compartments are secured safely to the other carrying case
- External strap to carry case around easily
- Clips on internal storage compartments for attaching to belts, straps etc - to enable individual compartments to be taken to the task in hand
- Dimensions: 300mm x 340mm x 145mm
-
Part no. ALB30952
Multi-Purpose Workshop Trolley / Cart
- Quality cart for automotive maintenacne applications
- Push hadle moulded into top shelf
- selection of shelf dividers supplied with multiple fitting options available
- 2x 100m (4") Brake Wheels / 2x 100m (4") Movable Wheels
- Will not scratch car finish due to plastic construction
- Uprights made from lightweight aluminium alloy
- Dimension: 575mm x 460mm x 900mm
- Self assembly
-
Part no. ALB30941
Oil Drain Pan for Motorbikes
- Sturdy moulded plastic
- 2.68L capacity
- For use with motorbikes
-
Part no. ALB30940
20L Drain Pan for Oil Drums
- Sturdy moulded plastic - fits directly on to 200L waste oil barrel
- 20L capacity
- Built-in empty directly into a 200 litre barrel
-
Part no. ALB30751
17 Litre Drain Pan (Black) For Engine/Gearbox Oil etc
- Made from sturdy moulded plastic
- 17L capacity
- Handy spout for emptying
-
Part no. ALB30752
17 Litre Drain Pan (Green)- For Coolant/Screenwash Etc
- Made from sturdy moulded plastic
- 17L capacity
- Handy spout for emptying
-
Part no. ALB30729
Oil Suction Gun 500ml
- Chrome plated T-bar handle plunger
- For removal of oil from different gear boxes
- 500ml capacity
- Supplied with 200mm flexible suction hose
-
Part no. ALB30584B
Professional Oil Drainer & Extractor
- Oil drainer with vacuum to extract oil via the dipstick
- 80L reservoir
- Oil level indicator tube
- Telescopic tube adjusts from 1200mm to 1950mm
- Extra large diameter drain pan & removable filter
- Safe air discharge of oil from tank
- No lifting, pouring or spillage
- For use on gearbox oil, automatic transmission oil & in motorcycles, in addition to normal engine oil draining
- Supplied complete with suction hose
- 4 industrial castors - 2 swivel, 2 braked
-
Part no. ALB30547A
Oil Drainer – 80Litre
- Easy, no mess way to drain & remove vehicle oil
- 80L reservoir
- Oil level indicator tube
- Telescopic tube adjusts from 1200mm to 1950mm
- 4 industrial castors, 2 swivel, 2 braked
- Extra large diameter drain pan & removable filter grid
- Safe air discharge of oil from tank
- No lifting, no pouring, no spills
-
Part no. ALB30537B
Manual Oil & Fluid Extractor 6.5Litres
- Manually operated, vacuum powered, oil & fluid extractor - no external power supply required
- Suitable for the extraction of all types of engine, transmission and lubricating oils from cars, motorcycles, marine and other types of engines
- Also suitable for low-viscosity fluids e.g. coolant, water etc
- Supplied with 6.7mm x 850mm & 5.8mm & 850mm suction probes & 9.5mm x 1.2m extension hose
- 6.5L capacity
- Portable unit, simple and easy to operate
-
Part no. ALB30733
Manual / Pneumatic Oil & Fluid Extractor -10 litres
- Combination fluid extractor - either compressed air or manually operated to generate vacuum for extraction
- Suitable for the extraction of all types of engine, transmission and lubricating oils from cars, motorcycles, marine and other types of engines
- Also suitable for low-viscosity fluids e.g coolant, water etc
- Allows extraction via dipstick
- Excellent vacuum
- Air or manual to pump waste fluid
-
Part no. ALB30812
Fuel Supply Line Connectors Kit for ALB30634A & ALB30914A (8pcs)
- Supplied with both ALB30634A and ALB30914A, but available separately for other applications
-
Part no. ALB30905
Alternator Free-Wheel Pulley Set – 22pcs
- Special set of spline & torx socket bits for the removal of free-wheel alternator pulleys
- Allows simple removal and installation of free-wheel alternator pulleys: on or off the vehicle
- Permits alternator, allowing the central locking bolt of the pulley to be released
- Can be used with hand tools or impact gun
- Fits most alternators by using interchangeable adaptors; including VW, Audi, Seat, Mercedes, Renault, BMW, Ford, Renault, Fiat etc.
-
Part no. ALB40039
Fuel & Injection Line Stopper Kit
- A wide-ranging kit designed to stop the flow of fuel from fuel lines after disconnection
- Also suitable for use with brake lines, transmission lines and other pipe applications
- Consists of 6x pairs of fuel supply clamps, and 6 x hose end stoppers
- Suitable for 3/16", 1/4", 5/16" pipe and banjo fittings
-
Part no. ALB30998
Fuel/ Air Conditioning Line Disconnect Set 22pcs
- Master kit for separating automotive air conditioning hoses and fuel lines
- Suitable for a wide variety of vehicles including Ford and Vauxhall/Opel
-
Part no. ALB30951
Fuel Tank Sender Wrench Set
- Essential tool for removing the retaining ring on fuel tank senders
- Select two or three jaw option
- Size ranges: 75mm-160m, 80mm-122mm, 110mm-170mm
-
Part no. ALB40004
Circlip Selection Kit 285pcs
- Kit contains: 15 of each approx internal circlips size: 10, 12, 14, 16, 18 and 20mm
- 5 of each approx external circlips size: 32mm
- 10 of each approx external circlips size: 20, 22 and 25mm
- 20 of each approx external circlips size: 6, 8, 10, 12, 14, 16 and 18mm
-
Part no. ALB40003
Circlip Plier Set (Inside & Outside)
- Adjustable heavy duty circlip pliers with interchangable internal and external ends, length 260mm
- Sizes range from 9mm-45mm (interchangable ends) 2x 45 degree angle - dia 2.25mm 2 x 15 degree angle - dia 2.25mm 2x 45 degree angle - dia 2.
- Set includes 90 degree & 45 degree internal and external pliers; Tip 1.2mm
-
Part no. ALB30960
4 Row Wire Brush
- Wooden handle with steel brush fill
- Suitable for general purpose applications
- Fill pattern: 4 rows of 14 bristles
-
Part no. ALB30965
Set of 3 Cranked Ratchet Handles- Heavy Duty
- Made from chrome vanadium steel
- Ultra-smooth 72-tooth ratchet for action use in confined areas - 1/4" - 3/8" - 1/2" sq dr
- Features: Flip reverse, push-button quick release, offset handle with comfort grip
-
Part no. ALB40099
Magnetic Parts Tray with LED Lights
- Stainless steel bowl with 80mm covered magnet - will not mark surfaces
- Ideal for storing nuts, bolts, screws, washers & sockets during assembly and disassembly
- Attaches to any ferrous surface & even works upside down
- Adjustable plastic cover to secure parts in horizontal or vertical position
- ~LED Light - ideal when working in poorly illuminated areas
-
Part no. ALB40037
Tap & Die Set with Ratchet 20pcs
- A wide-ranging tap & die set complete with essential accessories for completing the job
- 7pcs tap sizes- M3, M4, M5, M6, M8, M10, M12
- 7pcs die sizes- M3, M4, M5, M6, M8, M10, M12
- Taps & dies manufactured from high carbon steel
- Supplied with 2x tap chucks & 1 x die holder
- Kit includes a quick release 1/4" sq dr ratchet, extension bar 75mm & 2.5mm hex key
-
Part no. ALB30993
Socket & Bits Set with Pro Ratchet Wrench – 35pcs
Contents:- 1pcs double end ratchet wrench inclues 8mm & 10mm hex bit drivers 3pcs PH screwdriver bits - #1, #2, #3; 3 pcs Flat screwdriver - 4, 5.5, 6.5mm; 5pcs Hex bits - 3, 4, 5, 6, 8mm; 6pcs Security torx bits - T10, T15, T20, T25, T27, T30; 12 pcs Sockets : 4, 4.5, 5, 5.5, 6, 7, 8, 9, 10. 11, 12, 13mm 1pcs 1/4" sq dr socket adaptor, 1pcs 1/4" sq dr extenstion
-
Part no. ALB30957
Power Bits Set – 56 Pcs
- All sizes in both 30mm & 75mm lengths - 10mm hex
- Ribe bits; M5, M6, M7, M8, M10, M12, M14
- Spline bits; M5, M6, M8, M10, M12
- Hex bits; 4, 5, 6, 7, 8, 10, 12mm
- Security TRX-Star bits; T20H, T25H, T30H, T40H, T45H, T50H, T55H, T60H, Drive adaptors; 3/8" sq x 10mm Hex, 1/2" x 10mm Hex
-
Part no. ALB30868
Thor Double Copper Hammer
- Malleable iron head fitted with 2 x copper cylindrical faces
- Faces and head combine to provide the weight for the blow, while the copper faces prevent damage to expensive components and assemblies
- Ideal where a heavy blow is required combined with a relatively small striking area
- Faces designed to wear and can be replaced
- Use as a general purpose soft faced hammer in automotive and general engineering for assembly, repair and maintenance
- Size No. 2 - 38mm ( 1 1/2")
- Faces - 1260gms - 300mm (12" shaft)
-
Part no. ALB30860
Heavy Duty Prybar Set
- Set of four - heavy duty angled pry bar shafts, square profile bar with blackened finish
- Fitted with textured grip handle & hammer cap
- Set consists of - 6x200mm, 8x300mm, 11x460mm, 11x610mm
-
Part no. ALB30959
Hydraulic Puller & Separator Set
- Master set of gear pullers & bearing separators
- Forged steel bearing separator
- 10 tonne hydraulic ram
- 10 tonne hydraulic ram
- 3 x 100mm leg
- 3 x 150mm leg
- 3 x 200mm leg
- 1 x twin head, 1 x triple head
- Extension nose pieces; 1 x 50mm, 1 x 100mm
- Separator pulling rods; 4 x 200mm
- Twin pulling beam & separator 75-105mm
-
Part no. ALB40239
Wheel Nut Socket Set 5pce 15/17/19/21/22mm
- Chrome molybdenum 6 point wheel nut sockets suitable for use with impact tools
- Hardened, tempered and anodised for corrosion resistance
- Sockets are sleeved to protect alloy wheels & nuts
- Colour coded for easy size selection
- Sizes: 15mm, 17mm, 19mm, 21mm & 22mm - 1/2"sq dr
-
Part no. ALB40082
Tyre Deflator For TPMS Systems
- Prevents tyres & wheels being fitted incorrectly
- Identifies each tyre wheel & its position on the vehicle, as per the TPMS system
- Safety releases air from TPMS valves
- Colour coded & marked : LR - green, LF - yellow, RR - blue, RF - ref
-
Part no. ALB40040
Tyre Valve Removal & Installation Tool Kit
- Tyre Valve installer and remover tool kit- designed to remove and fit rubber tyre valves without removing the tyre
- Use the hook to remove the old valve body, the screw tool and tapered tube are used for fitting
- Ideal for replacing leaking valves on cars, vans and motorcycles
- Not suitable for use on tyres with TPMS- tyre pressure monitoring system
-
Part no. ALB30658
MOT Approved Digital Tyre Depth Gauge
- Measurement 0-10mm (metric and imperial)
- Resolution: 0.01mm
- Accuracy: +/- 0.01mm
- Sturdy plastic case
-
Part no. 30586
Digital Tyre Depth Gauge
- Measurement range - 0-25mm (metric and imperial)
- Tolerance +/- 0.05mm
- Sturdy plastic case
-
Part no. ALB40065
Master Thread Repair Kit
- Suitable for 5 common size thread; M5 x 0.8, M6 x 1.0, M8 x 1.25, M10 x 1.50, M12 x 1.75mm
- Ideal for repairing damaged or stripped internal threads
- Protects trapped threads against wear and damage
-
Part no. ALB30997
Glow Plug Thread Repair Kit 31pcs
- Re-threading kit for 8,10, 12mm glow plugs
- Replaceable consumable items available
- Suitable for alloy cylinder heads
- Tap sizes: M8 x 1.0, M10 x 1.0 & 1.25, M12 x 1.0 & 1.25 M14 x 1.25
- Coil sizes: M8 x 1.0, M10 x 1.0 & 1.25, M12 x 1.25
-
Part no. ALB40217
Shock Absorber Piston Clamp
- Universal protective clamp retains the piston rod in extended position
- Clamp has short and long screws to cover wide range of piston diameters:12-28mm
- Selection of hose connectors and brake bleed nipple adaptors
-
Part no. ALB40216
Shock Absorber Return Spring Puller
- Makes life easy when working on shock absorbers with internal rebound stop springs
- Saves times when assembling new shock absorbers
- Universal protective clamp retains the piston rod in extended position
- Clamp has short & long screws to cover wide range of piston diameters: 12-28mm
- Telescopic handles makes it easy to assemble the new piston
-
Part no. ALB30859
Coil Spring Compressor
- 1000kg (10200Nm) maximum jaw loading, with a 2.75 safety factor
- Supplied with 3 pairs of drop-forged jaws;80-110mm diameter, 88-160mm diameter & 126-212mm diameter
- Safety jaws shaped to prevent coil spring from bowing & slipping
- Suitable for use with 21mm combination spanner
- NOT SUITABLE FOR USE WITH AIR IMPACT WRENCHES
- Applications: Alfa, Audi, BMW, Citroen, Daihatsu, Fiat, Ford, GM, Honda, Jaguar, Lada, Lancia, Mazda, Mitsubishi, Nissan, Peugeot, Porsche, Renault, Rover, Saab, Seat, Skoda, Subaru, Suzuki, Toyota, Volvo, VW
-
Part no. ALB30956
Shock Absorber Master Tool Kit
- Comprehensive set of tools for dismantling & installing shock absorber strut assemblies
- Includes 9 special sockets & 25 bit inserts for releasing strut top nuts; 14-27mm sockets & slotted/torx/D shape/ hex male & female strut top bit inserts
- Also includes 5x traditional strut nut sockets (Audi, Rover, VAG etc)
-
Part no. ALB30657
Slide Hammer Puller Set 10pce
- Slide Hammer Hub Puller - 2.25kg Hammer weight
- Can be used in the following formats:
-
Part no. ALB30716
Slide Hammer Hub Puller 2.25KG Hammer
- Enables removal of flange type rear axle hubs from most vehicles & lightweight commercials
- Can be used on bolts up to 14mm diameter
- Fits 4-,5- or 6- bolt patterns and stud circles from 108mm to 141mm
- Hub pulling plate with 2.25kg slide hammer assembly
-
Part no. ALB40240, ALB40241
Wheel Hub Grinder Aluminium Body C/W Cleaning Disc
- Aluminium bell with steel core & 1/2" sq dr - for use with pneumatic impact wrenches
- Corrosion between the wheel rim & the wheel hub is removed effectively
- Torque values no longer distorted by a build up of corrosion
- Complete with 1x abrasive cleaning disc - 150mm diameter
-
Part no. ALB30861
Wheel Stud Cleaning Kit
- For cleaning corroded wheel studs and adjacent hub surfaces
- removes dirt and corrosion and prepares surfaces for correct torque application
- Ideal for preparing wheels, hubs & brake discs or drums for reassembly
- Suitable for use with power drill or air impact wrench
- Stud cleaner body including velcro pad; 2 x replacement velcro pads; 5 x fine cleaning discs; 5 x coarse cleaning discs
-
Part no. ALB40224
Bush Sleeve Kit
- Universal set of sleeves for removing and installing bushes, bearings etc
- For use in conjunction with bearing press support block ( eg ALB40097 or equivalent) & workshop press
- Standard universal applications: car, HGV, LCV
- 20 bush sleeves - ID range: 34.5 - 72.5mm, OD range: 43.5 - 82.5mm
- Adaptor plate for use with press block
-
Part no. ALB40097
Universal Bearing Press Support
- For use with a workshop press
- Press bearings fit easily on a variety of different suspension arms
- The three point contact provides a perfect, safe support
-
Part no. ALB40032
Video Borescope with Image & Video Capture
- Suitable for internal inspection of cyclinder head bores, engine compartments and other automotive & industrial applications
- Flexible shaft diameter is small enough to fit through most spark / glow plug & injector apertures
- Capable of taking photos/videos which can be viewed on computer via SD card
- Ideal for warranty authorisation
- Supplied with SD card, AV cable, battery charger and carry case
- 3.52 LCD monitor screen 320 x 240 pixels resolution
- 5.5mm diameter probe
- Automatic exposure camera
- 2GB memory SD card
- Re-chargeable internal battery, via mains cahrger
- Take, view & store single images, or videos
- View images/video on external screen via AV cable
-
Part no. ALB30926
Video Borescope & CCTV Camera Tester
- High Definition 2.4 TFT colour LCD Screen - 480 x 234 pixels (4.5mm x 3.5mm)
- Video input (via cable) & AV input (external source)
- Ideal for visual inspections in hard to reach areas
- Fully flexible waterproof cable
- Lightweight ergonomic design
- Easy to use Cable dimensions – 6mm diameter x 1m long
- Colour LCD – 4.5cm x 3.5cm
- Focussing distance 15 to 25cm
- Internal re-chargeable lithium battery, via USB cable
- Supplied with: magnet, hook, and mirror
- Adjustable light intensity – 6 levels
-
Part no. ALB30608AB
Refractometer- For Coolant, Battery Acid, Screenwash & Adblue
• Tests antifreeze, battery acid and screen wash • Supplied in sturdy plastic case • Complete with pipette and pouch • Adjustable eyepiece for easy focusing -
Part no. ALB30551AB
Refractometer- For Coolant, Battery Acid, Screenwash & Adblue
Tests Antifreeze, battery acid, AdBlue, & screenwash Automatic temperature compensation Adjustable eyepiece for easy focusing Supplied in sturdy plastic case, complete with pipette & pouch -
Part no. ALB40212
Relay Adaptor Set 2pcs
- Set of two adaptors to increase the range coverage of an existing relay tester
- The adaptor plugs into the relay tester & the relay to be tested then plugs into the appropriate adaptor
- For 4 & 5 pin relays as commonly used for fuel pumps and other powered components
-
Part no. ALB30933
Automotive Relay Tester
• Quickly tests 4 and 5 pin electro mechanical relays used on most cars • Checks for consistent functioning of relay contacts • Coil test voltage 9 volts • Automatically indicates test results with a series of red and green performance lights • 12v power supply required -
Part no. ALB40213
Relay Adaptor Set 3pcs
- Set of 3 adaptors which allow an existing relay tester to test shielded relays
- The shielded relay adaptor plugs into the same pin sockets as the normal relay and then the shielded relay then plugs into the adaptor
- Fits into any of the three 4 & 5 pin sockets on the relay tester
